You must log in to edit PetroWiki. Help with editing

Content of PetroWiki is intended for personal use only and to supplement, not replace, engineering judgment. SPE disclaims any and all liability for your use of such content. More information


Search results

Jump to navigation Jump to search
  • Well test (redirect from Well testing)
    generally run for a longer period of time. This is the most preferred well testing technique. The well is first produced at a constant rate till pressure
    9 KB (1,178 words) - 21:41, 4 November 2019
  • caveats for well testing, drawdown/buildup analyses and decline curve analysis for characterizing geothermal reservoirs. Geothermal well testing is similar
    40 KB (4,899 words) - 12:50, 3 June 2015
  • Types of logs (category 5.6.4 Drillstem or well testing)
    Over time, many different types of logs have been developed to collect data about wellbores and subsurface formations. This article provides an overview
    9 KB (777 words) - 13:10, 6 July 2015
  • Measurements of mass flow and the constituents of the mass produced are integral in the production of geothermal fluids. From regulatory and royalty payment
    17 KB (2,367 words) - 14:11, 16 July 2015
  • Single-point tests for gas wells (category 5.6.4 Drillstem or well testing)
    A single-point test for gas well deliverability is an attempt to overcome the limitation of long test times required for flow-after-flow tests. This article
    4 KB (390 words) - 13:07, 6 July 2015
  • Flow-after-flow tests for gas wells (category 5.6.4 Drillstem or well testing)
    This page discusses the implementation and analysis of flow-after-flow testing for gas well deliverability assessment. Both the Rawlins and Schellhardt
    11 KB (1,177 words) - 12:57, 6 July 2015
  • Acquiring bottomhole pressure and temperature data (category 5.6.4 Drillstem or well testing)
    shows a typical DST string with its essential components. In exploration well testing in particular, the DST string usually includes tubing-conveyed perforating
    18 KB (2,609 words) - 14:59, 26 June 2015
  • Designing single well chemical tracer test for residual oil (category 5.6.4 Drillstem or well testing)
    Using the single well chemical tracer (SWCT) test avoids the problems of too-wide well spacing and excessive tracer dispersion caused by layering that
    14 KB (2,007 words) - 15:37, 9 July 2015
  • performance Financial stability Honoring of contracts, etc. If extensive well testing is anticipated, burning and/or storage of the crude must be considered
    11 KB (1,596 words) - 13:19, 25 June 2015
  • Modified isochronal tests for gas wells (category 5.6.4 Drillstem or well testing)
    This article discusses the implementation and analysis of the modified isochroncal testing for gas well deliverability tests. Both the Rawlins and Schellhardt
    32 KB (3,241 words) - 17:06, 9 July 2015
  • expected ultimate recovery. Fig. 1-Plot of effective permeability (from well testing) vs. expected ultimate recovery (from material balance and simulation)
    26 KB (3,705 words) - 16:01, 19 January 2016
  • disturbance is proportional to the square root of time. This is why the well testing time necessary to observe distant boundaries becomes prohibitively expensive
    12 KB (1,635 words) - 11:53, 3 June 2015
  • occurrence. It is often used for bulk separation in conjunction with well testing as shown. The streams are temporarily separated, measured and analyzed
    17 KB (2,427 words) - 20:00, 8 December 2021
  • 2 Core analysis 5.6.3 Pressure transient analysis 5.6.4 Drillstem or well testing 5.6.5 Tracer test analysis 5.6.6 Cross well tomography 5.6.7 Formation
    44 KB (2,631 words) - 16:04, 10 February 2022
  • reservoir fluids through one large flowline rather than individual flowlines. Well testing is accomplished by installing a separate flowline with a valve manifold
    5 KB (623 words) - 13:35, 2 June 2015
  • spent to log wells and totally eliminate money spent on extras such as well testing. However, in these low-permeability layered systems, the engineers and
    25 KB (2,934 words) - 13:54, 16 July 2015
  • phase export Oil and condensate export Separator performance The need for well testing and overall production system optimization contributes to flow assurance
    4 KB (466 words) - 10:30, 15 January 2018
  • checking to keep them operating at their optimum effectiveness. Also, well testing is more difficult. Hydraulic systems are normally is used in areas where
    16 KB (2,392 words) - 13:40, 4 February 2016
  • thus eliminating the need to flare or burn the produced fluid during well testing. Table 1-Ultradeepwater Drillship Designs and general Characteristics
    6 KB (899 words) - 13:58, 26 June 2015
  • some wellbore length. This is called transmissivity and has units of m3. Well testing is discussed in Geothermal reservoir engineering. Reservoir temperature
    26 KB (3,966 words) - 01:55, 22 June 2021

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)