You must log in to edit PetroWiki. Help with editing
Content of PetroWiki is intended for personal use only and to supplement, not replace, engineering judgment. SPE disclaims any and all liability for your use of such content. More information
Search results
Jump to navigation
Jump to search
- A “well test” is simply a period of time during which the production of the well is measured, either at the well head with portable well test equipment9 KB (1,178 words) - 21:41, 4 November 2019
- instrument selection, and installation cannot be overemphasized. How and what well-test data are to be acquired (for reservoir management and well-system diagnostics)9 KB (1,364 words) - 13:51, 2 June 2015
- Manual. Richardson, Texas: SPE. Earlougher, R.C. Jr. 1977. Advances in Well Test Analysis, 5, 8, and 14. Richardson, Texas: Monograph Series, SPE. Gdanski9 KB (1,128 words) - 15:15, 1 July 2015
- estimates in vertical wells. Further, it is much more difficult to interpret well test data because of 3D flow geometry. The radial symmetry usually present in71 KB (6,533 words) - 20:01, 4 June 2015
- Dynamic data (section Well test data)down into five categories: geomechanical, fluid, production, tracer, and well test. Wikipedia. 2014. Dynamic data (11 August 2014 revision). http://en.wikipedia6 KB (836 words) - 12:26, 28 March 2016
- articles have properties that make them suitable for application in a well-to-well test in which dilution volumes are large. For small fields in which the requirement9 KB (1,351 words) - 08:47, 20 August 2018
- treatment substantially increases the ultimate recovery. Post-fracture well-test analyses are used to compute estimates of the propped fracture length,9 KB (990 words) - 12:38, 18 January 2016
- Fluid flow in hydraulically fractured wells (section Specialized methods for post-fracture well-test analysis)fractured wells. Often, identification of specific flow patterns can aid in well test analysis. Five distinct flow patterns (Fig. 1) occur in the fracture and35 KB (3,384 words) - 20:04, 4 June 2015
- Designing single well chemical tracer test for residual oil (section Flow of tracers during a well test)basis of available production flow rate from the test well. In a single-well test, tracers injected into a higher-permeability layer will be pushed farther14 KB (2,007 words) - 15:37, 9 July 2015
- (5): 545–548. http://dx.doi.org/10.1021/ie50317a010 Raghavan, R. 1993. Well Test Analysis, 28–31, 336–435. Englewood Cliffs, New Jersey: Petroleum Engineering9 KB (978 words) - 12:49, 6 July 2015
- extra-heavy-oil deposits. Conventional well-test approaches are irrelevant to CHOPS well assessment for the following reasons: No well-test interpretation equations22 KB (2,943 words) - 14:10, 19 January 2016
- For comparison, an error analysis performed for a standard James-tube well test in the Philippines is given in Table 2, with calculations for two types17 KB (2,367 words) - 14:11, 16 July 2015
- edition, 353–386. Oxford, UK: Oxford University Press. Raghavan, R. 1993. Well Test Analysis, 28–31, 336–435. Englewood Cliffs, New Jersey: Petroleum Engineering23 KB (2,246 words) - 10:32, 8 June 2015
- This article focuses on interpretation of well test data from wells completed in naturally fractured reservoirs. Because of the presence of two distinct27 KB (3,262 words) - 14:16, 16 July 2015
- assumptions on which conventional well-test analysis methods are based. Numerical simulators are useful for history matching well-test data when conventional analyses26 KB (3,705 words) - 16:01, 19 January 2016
- determine the most productive zones in a reservoir in real time, and obtain well test results while drilling. Skin factors on most underbalanced drilled wells16 KB (2,214 words) - 15:29, 26 June 2015
- especially when integrating static and dynamic information, such as core and well-test permeabilities. Cosentino suggested that the best way to integrate data34 KB (4,396 words) - 17:25, 16 July 2020
- to completion, injectivity testing is perhaps the most useful kind of well test. In contrast with a production test, cold water injection does not induce40 KB (4,899 words) - 12:50, 3 June 2015
- Isolation Equipment - Spec 19OH Sand Screen Equipment - Spec 19SS Downhole Well Test Tools - Spec 19TT Subsurface Completion Isolation (Barrier) Valves and10 KB (1,168 words) - 10:20, 21 December 2021
- with fracture gradients ranging from 0.7 to 1.3 psi/ft. Depending on the well-test results, the seams are completed in several different ways. In coal seams71 KB (10,027 words) - 16:01, 19 January 2016