You must log in to edit PetroWiki. Help with editing

Content of PetroWiki is intended for personal use only and to supplement, not replace, engineering judgment. SPE disclaims any and all liability for your use of such content. More information


Compressors

PetroWiki
Jump to navigation Jump to search

This page provides an overview of the primary categories of natural gas compressor services and a description of the different classifications and types of compressors available to the industry. Adiabatic and polytropic compression theory are discussed with supporting definition of terminology.

Compression theory

Specific topics relating to compression theory include:

  • Power requirement
  • Isentropic exponent
  • Compressibility factor
  • Intercooling
  • Adiabatic and polytropic efficiency
  • Actual and standard volume flow rates
  • Mass flow rates
  • Inlet and discharge pressures
  • Inlet and discharge temperatures
  • Adiabatic and polytropic head

Major components and construction features of centrifugal and reciprocating compressors are emphasized. Installation, safety, and maintenance considerations also are discussed in their erspective pages.

Oil and gas compressor uses

Compressors used in the oil and gas industry are divided into six groups according to their intended service. These are:

  • Flash gas compressors
  • Gas lift compressors
  • Reinjection compressors
  • Booster compressors
  • Vapor-recovery compressors
  • Casinghead compressors

Flash gas compressors

Flash gas compressors are used in oil handling facilities to compress gas that is “flashed” from a hydrocarbon liquid when the liquid flows from a higher pressure to a lower pressure separator. Flash gas compressors typically handle low flow rates and produce high compression ratios.

Gas lift compressors

Gas lift compressors are frequently used in oil handling facilities where compression of formation gases and gas lift gas is required. Gas lift compressor duty is frequently of low to medium throughput with high compression ratios. Many gas lift compressors are installed on offshore facilities.

Reinjection compressors

The reinjection of natural gas is employed to increase or to maintain oil production. Reinjection compressors can be required to deliver gas at discharge pressures in excess of 10,000 psi. Reinjection compressors also are used for underground storage of natural gas. Compressors, applied to these services, have large compression ratios, high power requirements, and low volume flow rates.

Booster compressors

Gas transmission through pipelines results in pressure drop because of friction losses. Booster compressors are used to restore the pressure drop from these losses. Selection of these compressors involves evaluating the economic trade-off of distance between pipeline boosting stations and life-cycle cost of each compressor station. Booster compressors also are used in fields that are experiencing pressure decline. Most centrifugal pipeline booster compressors are gas turbine driven, although the use of variable-speed motor drives is becoming more prevalent. Low-speed integral gas engine reciprocating compressors also are used for gas transmission applications. Booster compressors typically are designed for high throughput rates and low compression ratio. Many booster applications can be configured in a single-stage centrifugal compressor.

Vapor recovery compressors

Vapor recovery compressors are used to gather gas from tanks and other low-pressure equipment in the facility. Often the gas from a vapor recovery compressor is routed to a flash gas, gas lift, or booster compressor for further compression. Low suction pressures, high compression ratios, and low gas throughput rates characterize these compressors.

Casinghead compressors

Casinghead compressors are usually used with electric submersible pumps and rod pumps where formation gas is required to be separated downhole and then transported through the annulus. Often the compressor discharge is routed to either a booster or flash gas compressor or to a low-pressure gathering system. Like vapor recovery compressors, casinghead compressors operate with low suction pressures, high compression ratios, and low gas throughput rates.

Classification and types

Compressors are classified into two major categories:

Positive displacement compressors

Positive displacement compressors are further divided into:

Dynamic or kinetic compressors

Dynamic compressors are continuous-flow machines in which a rapidly rotating element accelerates the gas as it passes through the element, converting the velocity head into pressure, partially in the rotating element and partially in stationary diffusers or blades. Dynamic compressors are further divided into:

Compression theory

Both positive displacement and dynamic compressors are governed by a few basic principles derived from the laws of thermodynamics. This section defines terminology and discusses the operating principles essential for understanding compressor design, operation, and maintenance.

Isentropic (adiabatic) compression

An adiabatic process is one in which no heat is added or removed from the system. Adiabatic compression is expressed by

RTENOTITLE ................(1)

where k = Cp/Cv = ratio of specific heats, dimensionless.

Although compressors are designed to remove as much heat as possible, some heat gain is inevitable. Nevertheless, the adiabatic compression cycle is rather closely approached by most positive displacement compressors and is generally the base to which they are referred.

Polytropic compression

A polytropic process is one in which changes in gas characteristics during compression are considered. Dynamic compressors generally follow the polytropic cycle as defined by the formula

RTENOTITLE................(2)

where n = polytropic exponent.

The polytropic exponent n is experimentally determined for a given type of machine and may be lower or higher than the adiabatic exponent k. Because the value of n changes during the compression process, an average value is used.

When inlet and discharge pressures and temperatures are known, the polytropic exponent can be determined from the relationship

RTENOTITLE................(3)

Head

Head is simply the work expressed in foot pounds per pound of gas or N-m/kg. At a given compressor speed and capacity, the head developed by a centrifugal compressor is the same regardless of the nature of the gas being compressed. The pressure rise produced by the given amount of head varies with the density of the gas.

Isentropic (adiabatic) head

In an isentropic compression process, head is calculated by Eq. 4.

RTENOTITLE................(4)

where

His = isentropic head, ft-lbf/lbm,
zavg = average compressibility factor, dimensionless,
Ts = suction temperature, °R,
S = gas specific-gravity (standard atmospheric air = 1.00),
Pd = discharge pressure, psia,
and
Ps = suction pressure, psia.

Polytropic head

In a polytropic compression process, head is defined by

RTENOTITLE................(5)

where

Hp = polytropic head, ft-lbf/lbm,
and
ηp = polytropic efficiency.

Adiabatic or isentropic efficiency

Adiabatic efficiency is defined as the ratio of work output for an ideal isentropic compression process to the work input to develop the required head.

For a given compressor operating point, the actual or predicted isentropic efficiency can be calculated with Eq. 6.

RTENOTITLE................(6)

where

ηis = isentropic efficiency,
Ts = suction temperature, °R,
Td = discharge temperature (actual or predicted), °R,
and
k = ratio of specific heats, Cp/Cv.

Polytropic efficiency

The efficiency of the polytropic compression process is given by

RTENOTITLE................(7)

where ηp = polytropic efficiency.

Compressibility factory

The perfect gas equation derived from Charles’ and Boyle’s laws makes it possible to determine the weight of a given gas as determined by the equation

RTENOTITLE................(8)

where

P = pressure,
V = volume,
N = number of moles,
R = constant for a specific gas,
and
T = temperature.

In reality, all gases deviate from the ideal gas laws to some degree. This deviation is defined as a compressibility factor, z , applied as a multiplier to the basic formula. Therefore, Eq. 8 is modified to include the compressibility factor as shown next.

RTENOTITLE................(9)

Flow or capacity

Compressor flow (capacity) can be specified in three ways:

  • Mass (weight) flow
  • Standard volume flow
  • Actual (inlet) volume flow

Mass or weight flow

Mass flow is expressed as mass per unit of time, most often pounds-mass per minute (lbm/min) or kilograms per minute (kg/min). Mass flow is a specific value independent of gas properties and compressor inlet conditions. Mass flow can be specified on either a wet (water vapor included) or dry basis.

Standard volume flow

Standard volume flow is the most common term used by the industry to describe volumetric flow because it is independent of actual gas pressures or temperatures. It is the volume per unit of time using pressures and temperatures that have been corrected to "standard" conditions. These conditions apply to pressure, temperature, molecular weight, and compressibility. The standards must be known and held constant. For purposes of this text, the standard conditions used are

pressure = 14.7 psia,
temperature = 60 °F,
compressibility = 1.00,
and
molecular weight = MW of subject gas.

Standard volume flow is usually dry and expressed in millions of standard cubic feet per day (MMScf/D).

Actual inlet volume flow

Actual volume flow is defined as the amount of volume per unit of time at the inlet to the compressor. Actual volume flow is normally expressed in actual cubic feet per minute (ACFM) or actual cubic meters per hour (m3/hr). When gas composition and pressure and temperature are known, the specification of actual volume is appropriate because the fundamental performance characteristic of the compressor is sensitive only to actual volume flow at the inlet.

Mass flow can be converted to actual volume flow with Eq. 10.

RTENOTITLE................(10)

where

W = mass flow, lbm/min.,
R = universal gas constant = 1,545,
MW = molecular weight,
Ts = suction temperature, °R,
zs = compressibility at inlet,
and
Ps = absolute suction pressure, psia.

Standard volume flow can be converted to actual volume flow with Eq. 11.

RTENOTITLE................(11)

where Qg = standard volume flow, MMscf/D.

Compression ratio

Compression ratio, Rc, is simply the absolute discharge pressure divided by the absolute suction pressure. As expressed in Eq. 3, temperature ratio increases with pressure ratio. Temperature limits related to the mechanical design of compressors often will dictate the maximum pressure ratio that can be achieved in a stage of compression. (Refer to section on intercooling below.)

Intercooling

Where large pressure ratios are needed, splitting the compression duty into one or more stages with intercooling between stages can be the most energy efficient arrangement. The energy savings must be compared with the capital and maintenance investment necessary to provide the cooling. In addition to the thermodynamic benefit, intercooled compression systems result in lower discharge temperatures, which reduce the need for special compressor materials.

Power requirement

The total power requirement of a compressor for a given duty is the sum of the gas power and the friction power. The gas power is directly proportional to head and mass flow and inversely proportional to efficiency. Mechanical losses in the bearings and, to a lesser extent, in the seals are the primary source of friction power.

For centrifugal compressors, the gas power can be calculated as

RTENOTITLE................(12)

where

GHP = gas power, horsepower,
W = mass flow, lbm/min.,
and
Hp = polytropic head, ft-lbf/lbm.

For reciprocating compressors, the gas power can be calculated as

RTENOTITLE................(13)

where

P1 = inlet pressure, psia,
V1 = inlet volume, ACFM,
P2 = discharge pressure, psia,
and
CE = compression efficiency (assume 0.85 for estimating purposes).

Compressor selection

Proper selection of the compressor type and number of stages can be accomplished only after considering a number of factors. (For the purposes of this chapter, discussion is limited to centrifugal vs. reciprocating compressors.) Basic information needed for the proper selection includes:

  • Volume and mass flow of gas to be compressed
  • Suction pressure
  • Discharge pressure
  • Suction temperature
  • Gas specific gravity
  • Available types of drivers

The required volume flow and discharge pressure define a point on a graphic representation of compressor coverage, as shown in Fig. 6. Examination of this chart reveals that, in general, centrifugal compressors are appropriate for high flow applications, and reciprocating compressors are better suited to low flow rates.

Number of stages of compression

Using the specified overall pressure ratio and suction temperature (and an assumed efficiency), the discharge temperature for compression of gas with a known k value in a single stage can be estimated by rewriting Eq. 7.

RTENOTITLE................(14)

where

T2 = estimated absolute discharge temperature, °R,
T1 = specified absolute suction temperature, °R,
P1 = specified absolute suction pressure, psia,
P2 = specified absolute discharge pressure, psia,
k = ratio of specific heats,
ηp = assumed polytropic efficiency,
0.72 to 0.85 for centrifugal compressors,
and
1.00 for reciprocating compressors.

If the single-stage discharge temperature is too high (typical limit is 300 to 350 °F), it is necessary to configure the compression equipment in more than one stage. Calculating the compression ratio per stage with Eq. 15 does the evaluation of a multistage design.

RTENOTITLE................(15)

where

Rsect = compression ratio per section,
and
n = number of sections.

Using the previous equations and prudent assumptions, it is possible to determine the minimum number of stages required to accomplish a given overall compression ratio without exceeding temperature limits.

Nomenclature

k = Cp/Cv
Cp/Cv = ratio of specific heats, dimensionless
n = polytropic exponent
His = isentropic head, ft-lbf/lbm,
zavg = average compressibility factor, dimensionless,
Ts = suction temperature, °R,
S = gas specific-gravity (standard atmospheric air = 1.00),
Pd = discharge pressure, psia,
Ps = suction pressure, psia
Hp = polytropic head, ft-lbf/lbm,
ηp = polytropic efficiency
ηis = isentropic efficiency,
Ts = suction temperature, °R,
Td = discharge temperature (actual or predicted), °R,
k = ratio of specific heats, Cp/Cv
ηp = polytropic efficiency
P = pressure,
V = volume,
N = number of moles,
R = constant for a specific gas,
T = temperature
W = mass flow, lbm/min.,
R = universal gas constant = 1,545,
MW = molecular weight,
Ts = suction temperature, °R,
zs = compressibility at inlet,
Ps = absolute suction pressure, psia
Qg = standard volume flow, MMscf/D
GHP = gas power, horsepower,
W = mass flow, lbm/min.,
Hp = polytropic head, ft-lbf/lbm
P1 = inlet pressure, psia,
V1 = inlet volume, ACFM,
P2 = discharge pressure, psia,
CE = compression efficiency (assume 0.85 for estimating purposes)
T2 = estimated absolute discharge temperature, °R,
T1 = specified absolute suction temperature, °R,
P1 = specified absolute suction pressure, psia,
P2 = specified absolute discharge pressure, psia,
k = ratio of specific heats,
ηp = assumed polytropic efficiency,
0.72 to 0.85 for centrifugal compressors,
and
1.00 for reciprocating compressors
Rsect = compression ratio per section,
n = number of sections

References

Use this section for citation of items referenced in the text to show your sources. [The sources should be available to the reader, i.e., not an internal company document.]

Noteworthy papers in OnePetro

Use this section to list papers in OnePetro that a reader who wants to learn more should definitely read

External links

Use this section to provide links to relevant material on websites other than PetroWiki and OnePetro

See also

PEH:Compressors

Centrifugal compressor

Reciprocating compressor

Rotary positive displacement compressors